REOVIB 500 Series Phase-angle controller for vibratory feeders
Thyristor control units for use with vibratory feeder units
The REOVIB 500 range of control units are suitable for powering vibratory feeders which have a mechanical vibrating frequency which the same as, or double that of mains frequency.
The unit is supplied in a simple to install modular housing which is suitable for both DIN rail mounting (EN 50022-35) and back panel mounting.
-
REOVIB 506
IP 20, for DIN rail mounting
- Input voltage: 110 V, 230 V
- Output voltage: 20...105 V, 40...210 V V
- Output Current: max. 2 A
The REOVIB 506 is designed for controlling bowl or linear feeders up to 2A current rating. The output frequency 50Hz/100Hz (60Hz/120Hz) is selected to suit the feeder. In the regulation circuit there is built-in compensation for mains variations.
The feed rate setpoint is derived from a potentiometer and the setpoint range can be linearized by means of two trimmers Umin/Umax. Furthermore, an enable input is provided for start/stop operation.
Fixings are provided for DIN rail mounting according to EN 50022-35.
The equipment is available in IP 20 with 2 variations (Input voltage: 115V or 230 V):
- used with systems that have track control.
Typical applications
- Conveyor & assembly automation
- Conveyor technology
- Filling & packaging technology
-
REOVIB 509
IP 20, for DIN rail mounting
- Input voltage: 110 V, 230 V, 400 V
- Output voltage: 20...105 V, 40...210 V, 60...360 V
- Output Current: max. 15 A
The REOVIB 509 is designed for controlling bowl or linear feeders up to 15 A current rating. The output frequency 50Hz/100Hz (60Hz/120Hz) is selected to suit the feeder. In the regulation circuit there is built-in compensation for mains variations.
The feed rate setpoint can be derived from a potentiometer, a voltage signal 0...+10 VDC or a current signal 0...20 mA.
The setpoint range can be linearized by means of two trimmers Umin/Umax. Furthermore, an enable input is provided for start/stop operation and there is a control input for use with a track control module (REOVIB 513).
Fixings are provided for DIN rail mounting according to EN 50022-35.
The equipment is available in IP 20 with 3 variations (Input voltage: 115V, 230V or 400V):
- used with systems that have track control.
Typical applications
- Conveyor & assembly automation
- Conveyor technology
- Filling & packaging technology
-
REOVIB 514
IP 20, for DIN rail mounting
- Input voltage: 110 V, 230 V
- Output voltage: 20...105 V, 40...210 V V
- Output Current: max. 6 A
The REOVIB 514 is designed for controlling bowl or linear feeders up to 6 A current rating. The output frequency 50Hz/100Hz (60Hz/120Hz) is selected to suit the feeder. In the regulation circuit there is built-in compensation for mains variations.
The feed rate setpoint can be derived from a potentiometer, a voltage signal 0...+10 VDC or a current signal 0...20 mA. The setpoint range can be linearised by means of two trimmers Umin/Umax. Furthermore, an enable input is provided for start/stop operation and there is a control input for use with a track control module (REOVIB 513).
Fixings are provided for DIN rail mounting according to DIN EN 50022-35. .
The equipment is available in IP 20 with 2 variations (Input voltage: 115V or 230 V):
- used with systems that have track control.
Typical applications
- Conveyor & assembly automation
- Conveyor technology
- Filling & packaging technology
-
REOVIB 513
IP 00, for DIN rail mounting
- Input voltage: 110 V, 230 V
The REOVIB 513 track control module is used for regulating the storage of products on a track. It can be used with nearly all conventional proximity, (active) photoelectric, and Namur type sensors.
A selector switch in the front panel permits adaptation to the sensor characteristics (PNP/NPN output). Trimmers in the front panel provide adjustment of the On/Off switching delays within a range of 0.5....15 secs. The sensor state (damped or undamped) and also the enable input state (On/Off) state both have LED indicators. In addition a relay with changeover contacts, brought out to terminals, switches at the same time as the enable output.
Fixings are provided for DIN rail mounting according to EN 50022-35.
The equipment is available in IP 20 with 2 variations (Input voltage: 115V or 230 V):
- used with systems that have track control.
Typical applications
- Conveyor & assembly automation
- Conveyor technology
- Filling & packaging technology